COTTON PAINT EPOXY

Solvent Based Epoxy Topcoat Paint Product Description: It is a two-component, epoxy resin-based, reaction-drying, polyamide hardener cured, high chemical and mechanical resistance, bacteria-free, semi-gloss topcoat paint. Usage Area: It is used to protect metal surfaces of industrial steel structures, refineries, petrochemical and other industrial establishments, port facilities and shipyards, power plants, water and fuel tanks, waste water, malt industry facilities, pharmaceutical and food industry and hospitals from chemical and mechanical effects. . Application Method: Iron and Steel: Before the coating application, rust, oil, grease, dust and similar impurities on the surface should be removed. There should be no moisture on the application surface. On the sheet metal surfaces to be applied, the surface to be coated must be sandblasted to SA 2½ grade or mechanically cleaned to at least St 2 grade in accordance with the ISO 8501 standard. It should be covered with the selected primer paint within 4 hours following this process. If it is necessary to postpone the application, the surface should be sandblasted and cleaned again before priming. Other Metals and Alloys (Galvanized, Aluminum, etc.): After cleaning the surface with PMR Epoxy Thinner, a single layer of PMR Epoxy Primer should be applied. New Concrete, Cement Plaster: The surface must be cured for at least 28 days. Mortar residue on cured surfaces etc. should be removed by light sanding or brushing. Old Concrete, Cement Plaster: Old paint, dirt, dust, etc. on the surface. loose particles such as light sanding, scraping, brushing are removed. Oil and grease residues are cleaned with detergent and water. Concrete surfaces are impregnated with solvent-free epoxy primer. After that, the primer and intermediate coat paint must be sanded before the PMR Epoxy Topcoat to be applied. The main material is thoroughly mixed, then the hardener is added to the main material and mixed homogeneously for 3 minutes. After the mixture is rested for 15 minutes, the application is started. If at least 10 hours at 20 °C, and more than 48 hours at the most, the surface should be roughened to ensure good adhesion. Technical Specifications: General Information Appearance Semi-glossy Structure Epoxy Binder Resin Density ~1.65 gr/cm3 Thinner Epoxy Thinner Thinning Ratio 10% Color PMR Synthetic Group Chart Colors and Application Information in Desired Color Application Temperature 20°C, 50% RH Drying Time 7 Hours (20°C, 50% RH) Waiting Time Between Coats 10 – 24 Hours (20°C, 50% RH) Consumption 10 – 11 m2 with 1 Lt (60 micron dry film thickness) Recommended Primer PMR Epoxy Primer Application Tools Roll , Brush or airless spray Points to be Considered in Application: Before use, the paint should be mixed in the box until it becomes homogeneous. Application should not be made below +10 oC. Mixing time should be 2-5 minutes. The speed of the mixer should not exceed 400-500 rpm. Application surfaces must be dry and clean. The application should be made according to the specified application specifications. It should not be thinned more than 10%. Waiting times between coats must be observed. Cleaning of Application Tools: Application tools should be cleaned with PMR Epoxy Thinner immediately after use. Safety Warnings: S2 Keep out of reach of children. S16 Keep away from sources of ignition – No smoking S23 Do not breathe vapours. S29 Do not discharge into sewers. S36/37/39 Wear suitable protective clothing, gloves, eye/face protection. S46 If swallowed, seek medical advice immediately and show the container or label. Risk Warnings: R10 Flammable. R20/21/22 Harmful by inhalation, if swallowed and in contact with skin. R36/37/38 Irritating to eyes, respiratory system and skin. SUITABLE FOR TS 11590 Class2 / Type2